Recently one of the magnet holders for my window shutters broke, and I thought I'd take a crack at designing a replacement to 3D Print. I'd never designed anything in CAD software before, so I had no real reference.
I found FreeCAD extremely easy to use and intuitive. I watched a couple videos and followed-along with the tutorials, then started on my own item. It's a relatively simple 3-part component. I took measurements with digital calipers, and in a few hours was printing the first prototype.
A couple prototypes later (small measurement adjustments to account for plastic shrinkage, etc), I had the final model. Replaced all of the magnet holders since they were sure to go soon, too.
I had fun, and finally used my 3D printer for something "real". Pretty cool.
for incredibly simple parts that i can describe using measurements, i've had a lot of fun pointing a high-power ai at openscad and letting it iterate through making the design for me
it's still tough to turn it into something i can then keep fiddling with in freecad though
put on "tron: legacy" in the background to fully appreciate the model designing something that will be 3d-printed :)
Previously I'd get my calipers first and try to model using the direct measurements. The key point imo of the video was to take photos and model based on the photos, and then correct the measurements with your recorded measurements second.
That is the spirit! A friend recommended me to buy a Bambu P2S: there are parts I want to print and I don't want to model then send them to have them printed, nor to bother my friend all the time. Funnily enough I've got magnets falling too: for an alarm system on the doors/windows and they don't hold well anymore after the years. Then my car's radar detection device (fully legal) doesn't fit nicely in the phone holder I use to that effect: I want it a specific angle (I want it both inclined and facing towards me a bit). So I'll model those and just print them. There are a few things like that where I keep thinking: "If I had a 3D printer, I'd just print a part".
Most importantly: I've got a 11 y/o and I think it's cool for the kid to see how it works.
Already watch a few vids. Doesn't look too hard for simple things.
I post this in every FreeCAD thread: If you're going to start designing something with it, use the spreadsheet tool to make everything parametric. You'll save yourself a ton of time as your designs get more complicated.
Maybe this isn't anything new to experience CAD users. I don't know if other CAD tools do this as I started using FreeCAD after playing with 3D printing.
It's very common (Fusion calls it User Parameters, etc.) and indeed nice practice. FreeCAD has a few ways to do it, Spreadsheets but also free-form properties on objects. It's very flexible in this regard.
The only issue I have with the Spreadsheet is that I need to add an alias for every value I want to use in the Sketch or Part Design workbench. In practice, this usually looks like
A B
width 2mm
length 3mm
and for every cell in B I add an alias with the same value as in column A. Is there a way around that?
The Fusion implementation is awful - you can adjust one variable, one time, then you have to reopen the dialog to do another. At least for me it's always become non-responsive after a single edit, for years now. I've always assumed I'm just holding it wrong, but I don't know. I've moved on.
In coming time you can see freecad massively improving.
This space lacks good opensource solution.
I have tried creating my parts, tried tinkercad (which is simple but limited)
Tried fusion. And pretty much other things don't support mac.
I've a hunch lots of vibe coders are going to come and launch stuff like freecad and Gimp (which I never liked, can't even get simple tasks done in gimp)
Future is bright for opensource powered by LLM coding on steroids.
Slightly unrelated to this story, but I’m curious if anyone has good resources for learning FreeCAD. I have quite a lot of experience with SolidWorks, AutoCAD, OnShape, and similar software, but FreeCAD has always been hard for me to pick up.
Oh wow - over on Reddit, someone mentioned that the Deltahedra YouTuber has started using his own voice, rather than a generated one - and - well, his content is now far more watchable than it was previously!
YouTube was very effective for me to learn FreeCAD. I just searched for some FreeCAD tutorials and followed-along. I had zero prior CAD experience though, so I was a "blank slate" in a way.
FreeCAD is really the only serious contender for CAD on Linux. I love how everything is hackable via Python APIs. Every release seems to fix more and more UX issues. I have very high hopes for it to eventually start attracting more commercial usage, much like KiCad and Blender did in their spaces. We need more open software like that.
DeltaHedra, another great YouTube channel, also released a good video that shows the previous and this version next to each other: https://www.youtube.com/watch?v=bYdobpjTypg
Thumbs up for both of them, but I must say that DeltaHedra has become my new favourite FreeCAD content creator. Especially after he started using his own voice. His old content was good, but his current his magnifique! The quality of the content he pushes is above and beyond.
TL;DR: I wish they'd just align with Blender on UX, TBH.
I wish they settled on a nicer UX with less visual clutter. I use Blender and it is a _massively_ more complex application in every regard, yet its right-aligned panel and progressive exposure of toolbars feels infinitely more polished than FreeCad's clunky panel (which is often rendered with huge, oversized fields and buttons) and their legendary five-stacked toolbars.
Feels like that satirical Gillette ad, and is much harder to use and navigate, especially since quite a few UX options need to be turned on in Preferences to be usable...
I was not expecting so many improvements in this version alone, I'm impressed. I was already using it for 3d printing but now it seems it's getting actually good, makes me wonder how I was able to use the previous version.
I am also impressed by how much they are improving things. It just sucks that they are stuck with the OpenCasacade kernel so making stability improvements are hard to make in areas like fillets and others.
I don't follow Open CASCADE very closely, but it looks like they're on the verge of a new major release (v8.0) themselves that looks like a lot of refactoring and cleanup.
I don't know hat version FreeCAD is actually bundling, but from GitHub it looks like a fork of 7.8.1?
Recently one of the magnet holders for my window shutters broke, and I thought I'd take a crack at designing a replacement to 3D Print. I'd never designed anything in CAD software before, so I had no real reference.
I found FreeCAD extremely easy to use and intuitive. I watched a couple videos and followed-along with the tutorials, then started on my own item. It's a relatively simple 3-part component. I took measurements with digital calipers, and in a few hours was printing the first prototype.
A couple prototypes later (small measurement adjustments to account for plastic shrinkage, etc), I had the final model. Replaced all of the magnet holders since they were sure to go soon, too.
I had fun, and finally used my 3D printer for something "real". Pretty cool.
for incredibly simple parts that i can describe using measurements, i've had a lot of fun pointing a high-power ai at openscad and letting it iterate through making the design for me
it's still tough to turn it into something i can then keep fiddling with in freecad though
put on "tron: legacy" in the background to fully appreciate the model designing something that will be 3d-printed :)
I had a hard time but I didn’t start with the tutorial first.
But once I saw their “philosophy” as it were, everything became so much easier.
Learning to design parts was a huge "unlock" for me.
Wasn't just printing other people's designs.
Great feeling to measure and design something then have it fit perfectly.
I just saw a great video on how to replicate parts for printing https://www.youtube.com/watch?v=OcMvTfUfNXo
Previously I'd get my calipers first and try to model using the direct measurements. The key point imo of the video was to take photos and model based on the photos, and then correct the measurements with your recorded measurements second.
That is the spirit! A friend recommended me to buy a Bambu P2S: there are parts I want to print and I don't want to model then send them to have them printed, nor to bother my friend all the time. Funnily enough I've got magnets falling too: for an alarm system on the doors/windows and they don't hold well anymore after the years. Then my car's radar detection device (fully legal) doesn't fit nicely in the phone holder I use to that effect: I want it a specific angle (I want it both inclined and facing towards me a bit). So I'll model those and just print them. There are a few things like that where I keep thinking: "If I had a 3D printer, I'd just print a part".
Most importantly: I've got a 11 y/o and I think it's cool for the kid to see how it works.
Already watch a few vids. Doesn't look too hard for simple things.
I post this in every FreeCAD thread: If you're going to start designing something with it, use the spreadsheet tool to make everything parametric. You'll save yourself a ton of time as your designs get more complicated.
Maybe this isn't anything new to experience CAD users. I don't know if other CAD tools do this as I started using FreeCAD after playing with 3D printing.
You can also use VarSet[0], which I think is easier than spreadsheet since you don't have to switch the workbench.
[0]: https://wiki.freecad.org/Std_VarSet
Did not know about this. How do you see all the properties?
It's very common (Fusion calls it User Parameters, etc.) and indeed nice practice. FreeCAD has a few ways to do it, Spreadsheets but also free-form properties on objects. It's very flexible in this regard.
The Fusion implementation sucks. A spreadsheet is a far more natural way to do this, Im surprised FreeCad is doing it better than the paid variant.
The only issue I have with the Spreadsheet is that I need to add an alias for every value I want to use in the Sketch or Part Design workbench. In practice, this usually looks like
and for every cell in B I add an alias with the same value as in column A. Is there a way around that?VarSets[0] introduced recently in 1.0 and mentioned in a grand-aunt comment are a good alternative to spreadsheets used this way.
[0]: https://wiki.freecad.org/Std_VarSet
https://wiki.freecad.org/Macro_EasyAlias
EasyAlias macro maybe?
Oh. I didn't even know there were macros. But that looks very useful!
Hmmm - I seem to recall there was at least 1-2 scripts or macros available to help with aliasing.
The Fusion implementation is awful - you can adjust one variable, one time, then you have to reopen the dialog to do another. At least for me it's always become non-responsive after a single edit, for years now. I've always assumed I'm just holding it wrong, but I don't know. I've moved on.
Super flexible. I love being able to use Python to manipulate spreadsheet data.
Some CAD systems, i think NX for example, let you give it a reference to an actual Excel (or csv?) file, that you edit in Excel.
Or don't and adjust it in the sketcher? If you name your constrains you can just reference them directly elsewhere.
I think that's much easier as you don't have to go back and forth with a spreadsheet.
Other cad tools do support this but in my experience it's always pretty awkward to use. I haven't tried the FreeCAD implementation.
[delayed]
In coming time you can see freecad massively improving.
This space lacks good opensource solution.
I have tried creating my parts, tried tinkercad (which is simple but limited)
Tried fusion. And pretty much other things don't support mac.
I've a hunch lots of vibe coders are going to come and launch stuff like freecad and Gimp (which I never liked, can't even get simple tasks done in gimp)
Future is bright for opensource powered by LLM coding on steroids.
Slightly unrelated to this story, but I’m curious if anyone has good resources for learning FreeCAD. I have quite a lot of experience with SolidWorks, AutoCAD, OnShape, and similar software, but FreeCAD has always been hard for me to pick up.
I often recommend https://youtube.com/@deltahedra3d - some good tutorial videos and other excellent FreeCAD content.
MangoJelly on YouTube was my primary learning source, and a few other channels - but his "gelled" with me the best.
My goal this year is to finish his 40ish hour course. Excellent quality course at a good pace.
Oh wow - over on Reddit, someone mentioned that the Deltahedra YouTuber has started using his own voice, rather than a generated one - and - well, his content is now far more watchable than it was previously!
Yup, mine too. He has a course on Udemy as well.
YouTube was very effective for me to learn FreeCAD. I just searched for some FreeCAD tutorials and followed-along. I had zero prior CAD experience though, so I was a "blank slate" in a way.
FreeCAD is really the only serious contender for CAD on Linux. I love how everything is hackable via Python APIs. Every release seems to fix more and more UX issues. I have very high hopes for it to eventually start attracting more commercial usage, much like KiCad and Blender did in their spaces. We need more open software like that.
Highlights reel: https://www.youtube.com/watch?v=a9biWv_M8p8
Release Notes: https://wiki.freecad.org/Release_notes_1.1
To add to this. MangoJelly offers very good tutorials, as well as a full course on Udemy. He released a 4 minute overview: https://www.youtube.com/watch?v=mSwvnZ1jsXg
DeltaHedra, another great YouTube channel, also released a good video that shows the previous and this version next to each other: https://www.youtube.com/watch?v=bYdobpjTypg
Thumbs up for both of them, but I must say that DeltaHedra has become my new favourite FreeCAD content creator. Especially after he started using his own voice. His old content was good, but his current his magnifique! The quality of the content he pushes is above and beyond.
This is awesome! Kudos to the developers, they really went above and beyond for this release.
Congrats - the release video is very impressive !
TL;DR: I wish they'd just align with Blender on UX, TBH.
I wish they settled on a nicer UX with less visual clutter. I use Blender and it is a _massively_ more complex application in every regard, yet its right-aligned panel and progressive exposure of toolbars feels infinitely more polished than FreeCad's clunky panel (which is often rendered with huge, oversized fields and buttons) and their legendary five-stacked toolbars.
Feels like that satirical Gillette ad, and is much harder to use and navigate, especially since quite a few UX options need to be turned on in Preferences to be usable...
I was not expecting so many improvements in this version alone, I'm impressed. I was already using it for 3d printing but now it seems it's getting actually good, makes me wonder how I was able to use the previous version.
This is great to hear. I tried it a few years ago, and it was just so far behind onshape and fusion for usability from a beginner perspective.
This is single want to give it another chance
I am also impressed by how much they are improving things. It just sucks that they are stuck with the OpenCasacade kernel so making stability improvements are hard to make in areas like fillets and others.
I don't follow Open CASCADE very closely, but it looks like they're on the verge of a new major release (v8.0) themselves that looks like a lot of refactoring and cleanup.
I don't know hat version FreeCAD is actually bundling, but from GitHub it looks like a fork of 7.8.1?